Hitachi CP-X206 Manual do Utilizador

1ProjectorCP-X206/CP-X306User's Manual (detailed)TechnicalResolution (H x V) H. frequency (kHz) V. frequency (Hz) Rating Signal mode720 x 400 37.

10Command Control via the Network (continued)Command Format[TCP #23]1. ProtocolConsist of header (7 bytes) + command data (6 bytes)2. HeaderBE + EF +

11Command Control via the Network (continued)Decreasing the projector setting value (Decrement command)(1) The PC sends the following decrement code t

12Command Control via the Network (continued)7. Reply DataThe connection ID (the data is same as the connection ID data on the sending data format)

13Names  Operation Type HeaderCommand DataCRC Action Type Setting CodePowerSet Turn off BE  EF 03 06  00 2A  D3 01  00 00  60 00  00Turn on BE  EF03 0

14Names  Operation Type HeaderCommand DataCRC Action Type Setting CodeUser Gamma Pattern Set Off BE  EF 03 06  00 FB  FA 01  00 80  30 00  009 steps g

15Names  Operation Type HeaderCommand DataCRC Action Type Setting CodeCOLOR TEMP GAIN B Get BE  EF 03 06  00 8C  F5 02  00 B3  30 00  00Increment BE  

16RS-232C communication/Network Command table (continued)Names  Operation Type HeaderCommand DataCRC Action Type Setting CodeOVER SCAN Get BE  EF 03 0

17RS-232C communication/Network Command table (continued)Names Operation Type HeaderCommand DataCRC Action Type Setting CodeFRAME LOCK – COMPUTER1Set

18RS-232C communication/Network Command table (continued)Names Operation Type HeaderCommand DataCRC Action Type Setting CodeMONITOR OUT - COMPONENTSet

19RS-232C communication/Network Command table (continued)Names  Operation Type HeaderCommand DataCRC Action Type Setting CodeAUDIO-S-VIDEO Set AUDIO1

2Initial set signalsInitial set signalsThe following signals are used for the initial settings. The signal timing of some PC models may be different.

20RS-232C communication/Network Command table (continued)Names  Operation Type HeaderCommand DataCRC Action Type Setting CodeBLANK Set MyScreen BE  EF

21RS-232C communication/Network Command table (continued)Names  Operation Type HeaderCommand DataCRC Action Type Setting CodeMY BUTTON-1Set COMPUTER1B

22RS-232C communication/Network Command table (continued)Names  Operation Type HeaderCommand DataCRC Action Type Setting CodeCLOSED CAPTIONCHANNELSet

3Connection to the portsACOMPUTER IN1, BCOMPUTER IN2, CMONITOR OUT D-sub 15pin mini shrink jack• Video signal: RGB separate, Analog, 0.7Vp-p, 75Ω ter

4LANConnection to the ports (continued)4321HVIDEORCA jack• System: NTSC, PAL, SECAM, PAL-M, PAL-N, NTSC4.43• 1.0±0.1Vp-p, 75Ω terminatorGS-VIDEOMini D

5Connection to the ports (continued)IAUDIO IN1, JAUDIO IN2Ø3.5 stereo mini jack• 200 mVrms 47kΩ terminatorAUDIO IN3 KL, LRRCA jack x2• 200 mVrms 47kΩ

6Connection to the ports (continued)NUSBUSB B type jackPin Signal1 +5V2 - Data3 + Data4 Ground2134LANONOCONTROLD-sub 9pin plug• About the details of R

7RS-232C CommunicationRS-232C CommunicationConnecting the cable1. Turn off the projector and the computer. 2. Connect the CONTROL port of the projecto

8RS-232C Communication (continued)Requesting projector status (Get command)(1) Send the following request code from the PC to the projector. Header +

9Command Control via the NetworkCommunication PortThe following two ports are assigned for the command control.TCP #23TCP #9715Command Control Setting